Why is my VXL 3s blinking red?

Why is my VXL 3s blinking red?

When the battery voltage attempts to fall below the minimum threshold, the VXL-3s will shut down all motor output. The LED on the speed control will slowly blink red, indicating a low voltage shutdown. The VXL-3s will stay in this mode until a fully charged battery is connected.

What to do when ESC flashes red and green?

Note: A common cause of a red/green flashing LED is holding the EZ-Set button too long when turning a vehicle off. To prevent this, simply unplug the battery to turn the vehicle off, instead of holding the EZ-Set button.

Can you run LiPo on xl5?

The XL-5 features a completely waterproof design, three throttle profiles, low voltage detection, Thermal Shutdown Protection, 4-7 cell NiMH and 2-cell LiPo compatibility, and built-in BEC.

Can I use LiPo battery with xl5?

The XL-5 speed control is able to use LiPo batteries with nominal voltage not to exceed 7.4 volts (2S packs).

How do I change my Traxxas to NiMH mode?

Continue holding full reverse and the light on the ESC will stay green. Continue to hold full reverse, at the same time, press and hold the EZ-Set button on the ESC for the normal 10-12 seconds until the ESC is back in NiMH mode. NiMH mode is indicated by a solid red light on the ESC.

How do I sync my Traxxas remote to my car?

How to Bind Your Traxxas Transmitter to the Receiver

1. Step 1: Turn the Power Off.
2. Step 2: Access the Link Button on the Receiver.
3. Step 3: Press and Hold the Set Button on the Transmitter.
4. Step 4: Press and Hold the Link Button on the Receiver.
5. Step 5: Wait for a Solid Green LED.
6. Step 6: Enjoy Your Traxxas Vehicle.

Can a xl5 handle 3S LiPo?

Product Description. The Traxxas 3025 XL-5 HV brushed electronic speed control works with the high-voltage 3S LiPo battery packs for greater efficiency and power.

How many volts can a Traxxas xl5 handle?

4-7 NiMH cells or 2 LiPo cells (2S) Only: The XL-5 can only accept a maximum input voltage of 8.4 volts.

Can you run 3S in xl5?

The Traxxas 3025 XL-5 HV brushed electronic speed control works with the high-voltage 3S LiPo battery packs for greater efficiency and power.

Can you charge a NiMH battery with a LiPo charger?

A LiPO charger CAN charge several battery chemistries and NiMH IS one it can do.

How to install the vxl-3s?

Pour les installations sans la pièce #3725, le VXL-3s peut être installé dans le châssis avec un ruban adhésif à double face (voir l’illustration montrant le Traxxas Rustler). Les blocs de fixation doivent être découpés du boîtier avec des pinces coupantes de côté pour permettre au VXL-3s de se mettre en place dans la cosse sur le côté du châssis.

How does the vxl-3m™ work?

The VXL-3m™ uses advanced circuit design that allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. It sets up, operates, and programs just like the Traxxas XL-5™ family of ESCs so there’s no tricky new procedures to learn.

What are the characteristics of the vxl-3s?

Sur le VXL-3s, le fil rouge est positif, le fil noir est négatif et le fil blanc est le fil de contrôle. Attention : Sur certains systèmes radio Airtronics® plus anciens, les bornes positives et négatives sont contraires à celles du VXL-3s et il faut utiliser un adaptateur.

Can Traxxas be used for vxl-3s?

Puisque Traxxas n’a aucun contrôle de l’utilisation et les installations ultérieures du VXL-3s, aucune responsabilité ne peut être assumée ni ne sera acceptée pour tout dommage résultant de l’utilisation de ce produit. Chaque ESC est soigneusement mis à l’essai et rodé dans les ateliers de Traxxas et sera, par conséquent, considéré fonctionnel.