What is BEC voltage?
A BEC is basically a step down voltage regulator. It will take your main battery voltage (e.g. 11.1 Volts) and reduce it down to ~5 Volts to safely power your receiver and servos. What are the advantages of a BEC? If you are flying electric, a BEC is better than a battery pack in nearly all cases.
What is CC BEC?
CC BEC (Battery Eliminator Circuit) is a small device that eliminates the need for a receiver battery. It draws voltage from the motor batteries and drops it to a voltage level that is suitable for your receiver and servos.
What is BEC regulator?
In battery-powered equipment, a battery eliminator circuit (BEC) is an electronic voltage regulator used to power a subsystem at a different voltage without the need for a supplemental battery. BECs are commonly used in radio-controlled models, which need separate voltages to power the motor and the R/C equipment.
Is Castle BEC waterproof?
design capable of 14 amps peak, perfect for sport flying, helicopters, and UAVs. Racers, crawlers, and other splashers can now integrate a 15-amp peak power regulator in a waterproof (WP), CNC machined, aluminum case.
How do you use BEC?
The BEC has a receiver plug which needs to be installed into the AUX or BAT port on your ESC. The other end of it features two wires; a positive and negative. They should be soldered directly into the battery connecting wires on your ESC, red to red, black to black. This is how the BEC gets direct power.
How does a battery eliminator circuit work?
A battery eliminator circuit is a voltage regulator. It is designed to drop a big voltage down to a smaller voltage. As modern RC airplanes use high voltage batteries, it allows you to run your receiver, servos and other accessories from your main battery without using a seperate lower voltage one.
What is the difference between BEC and UBEC?
The BEC is linear while the UBEC is considered a switch mode BEC. The BEC has a more undisturbed signal an voltage and cheaper to manufacture. Adversely, they are less efficient and generate higher temperatures at greater voltages. The UBEC generally handles higher voltages, runs cooler and is more efficient.
How much voltage does a RC receiver put out?
4.8 to 6.0 volts
A good, clean power supply is important. Our RC radios typically require a DC voltage of 4.8 to 6.0 volts. On an oscilloscope, this DC voltage would appear as a straight line, so in this case, a flat line is a good thing. An oscilloscope is a voltage meter that displays the voltage with respect to time.
Do I need a BEC with ESC?
Most ESC’s (Electronic Speed Controllers) have a separate circuit built in called a BEC (Battery Eliminating Circuit). The BEC is used to supply power to the receiver and servos. Contrary to popular belief the BEC does not cut power to the motor when the battery voltage is low.
What voltage are RC servos?
4.8 V DC
RC servos use a three-pin 0.1″ spacing jack (female) which mates to standard 0.025″ square pins. The most common order is signal, +voltage, ground. The standard voltage is 4.8 V DC, however 6 V and 12 V is also used on a few servos. The control signal is a digital PWM signal with a 50 Hz frame rate.
How many volts does a receiver have?
Most receivers and servos can take 5 cells (6 volts).
What is the power output of the CC Bec pro?
The CC BEC Pro is designed to operate at up to 12S LiPo (50.4V) with a 20A* peak servo load. Generally used for 1/5 scale cars or cars utilizing multiple high powered digital servos, lights, winches and other accessories.
What is CCB Bec Pro (battery eliminator circuit)?
CC BEC Pro (Battery Eliminator Circuit) is a small device that eliminates the need for a receiver battery. It draws voltage from the motor batteries and drops it to a voltage level that is suitable for your receiver and servos.
Why choose the CC Bec?
The CC BEC 2.0 complements our established line of BECs hobbyists have relied on for years. With hundreds of thousands in the field, users can count on this new design to power today’s high-power, digital servos and accessories safely. The CC BEC 2.0 features heavy duty, dual output wires that will provide clean power to sensitive radio equipment.
Do I need a BEC Pro for my ESC?
This is required in applications which use high-power servos, where the ESC does not have an internal BEC, or the existing BEC is inadequate. The CC BEC Pro is designed to operate at up to 12S LiPo (50.4V) with a 20A* peak servo load.