Why is no beer coming out of my kegerator?

Why is no beer coming out of my kegerator?

Check that there are no obstructions in the air line. Check air line, CO2 regulator, and gauge. Regulators will wear down and typically need to be replaced after 4-6 years. Make sure CO2 pressure is ON; do not run the system off the keg pressure alone.

Why did my keg stop pouring?

If the brewer is using a blend, and the nitrogen content is too high, that may mean that too little CO2 is being used or that the pressure is too low, which can prevent beer from coming out of the tap—or cause the beer to pour flat.

Why is my mini keg not pouring?

Inspect the beer line for kinks or bends that may cause uneven flow of beer from the mini-keg. To do so, open the side of the unit and check to ensure that the tube between the tap and the faucet is free from obstruction and not kinked in any way.

Why is my kegerator spitting?

The most common causes are: Incorrect Temperature – If the beer is too warm or too cold, it will be more easily disturbed and pour as foam. In most models, the beer line is not refrigerated so the first pour will usually be a bit warmer and a bit more foam.

Why is my keg pump not working?

You should make sure the handles and flanges are not engaged before turning on the tap. Then set the party pump on top of the keg and lock it into place by turning it clockwise. If you see bubbles, disengage the pump and try again.

How do you get air out of a keg line?

1. Connect the tap line to the tap itself.
2. Place the cup underneath the tap to catch any liquid coming through it, and open the tap.
3. Raise the disconnected end of the tap line above the level of the tap and pour cold water into it.
4. Connect the disconnected end of the line to the keg.

Why does my keg keep foaming?

Keg care basics for your bar or restaurant Let the keg settle after moving it – If you move your keg, give it some time to settle down. If you don’t, you’ll probably experience excessive foaming when you tap it. Just like soda, beer is carbonated – and just like soda, it will foam when you shake it.

How do I fix my kegerator?

If there is, defrost your kegerator….Our 6-Step Guide to Making Your Kegerator Cool

1. Step 1: Check for Ice.
2. Step 2: Defrost Your Kegerator.
3. Step 3: Make Sure the Seal is Good.
4. Step 4: Get the Air Moving.
5. Step 5: Recalibrate the Thermostat.
6. Step 6: Check the Compressor Relay.
7. Step 7: Call the Experts.

Why am I getting air in my beer lines?

If your serving pressure is too high, it can pump excess co2 into the keg and lead to foaming. Check your regulator and adjust as required. If your serving pressure is too low, you may notice air pockets and bubbles in the beer line, causing foaming. Increase the serving pressure to ensure a solid flow.

Why is my Kegerator pouring foam?

When the temperature rises above 40 degrees, the CO2 gas starts to escape from the beer, and this is what causes foam (in most cases). For this reason, temperature issues constitute the great majority of problems with kegerators serving foamy beer.

How do you fix a foamy kegerator?

Tips for Reducing Kegerator Foam

1. Step 1: Temperature should be mid-low 40’s F (liquid temp, not air temp).
2. Step 2: Clean the beer line or replace.
3. Step 3: Beer line should be 3/16″ diameter.
4. Step 4: Use beer line that is 8 feet long.
5. Step 5: Set regulator in the 5-10 PSI range.

How do I stop my kegerator from foaming?

How do you fix a foamy keg?

Over carbonated – if you are getting a lot of foam and the drink has carbonation when you taste it it may be over carbonated. You can adjust it by releasing some pressure, letting it sit for an hour then releasing some more pressure.

How do I get rid of an airlock in my beer line?

What do I do if I have a problem with my kegerator?

If you are experiencing problems with your kegerator, please refer to our troubleshooting guide below. If your problem is not found below or you are unable to correct an issue you find on the chart, please leave a comment and/or give us a call at 1-866-950-8710.

What happens if the outside of a kegerator gets icy?

When the outside of your kegerator starts getting icy, it can really compromise the flavor and quality of your beer. For this reason, you want to be sure to defrost your kegerator on a regular basis and examine it for any signs of icing.

Are there any kegco kegerator problems like summit kegerators?

No matter the brand, kegco kegerator problems are going likely going to be similar to summit kegerator problems. This is simply because they all are modeled and function pretty much the same way. If you experience any of these issues, know that they’re very common and often an easy fix that you can do yourself.

Are there any problems with my EdgeStar kegerator?

Since kegerators can be very closely compared to a mini fridge, it’s easy to see how over time and many uses, your kegerator will begin to have some issues. Edgestar kegerator problems are similar to danby kegerator problems and so on. Luckily, the majority of the problems are easily fixable.