How do I reconstitute INVANZ 1g?
1. Reconstitute the contents of a 1 g vial of INVANZ with 10 mL of one of the following: Water for Injection, 0.9% Sodium Chloride Injection or Bacteriostatic Water for Injection, using a syringe equipped with a 21-gauge or smaller diameter needle. NOTE: Use with a needleless IV system is not recommended.
How do you reconstitute ertapenem?
(IV): Reconstitute 1 gram vial with 10 mL of Water for Injection, 0.9% Sodium Chloride Injection, or Bacteriostatic Water for Injection and then add contents to 50 ml normal saline. Complete the infusion within 6 hours of reconstitution.
How much lidocaine do you mix with INVANZ?
INVANZ MUST BE RECONSTITUTED PRIOR TO ADMINISTRATION. Reconstitute the contents of a 1 g vial of INVANZ with 3.2 mL of 1.0% lidocaine HCl injection2 (without epinephrine). Shake vial thoroughly to form solution.
How do you administer INVANZ injection?
INVANZ MUST BE RECONSTITUTED PRIOR TO ADMINISTRATION. Immediately withdraw the contents of the vial and administer by deep intramuscular injection into a large muscle mass (such as the gluteal muscles or lateral part of the thigh). The  reconstituted IM solution should be used within 1 hour after preparation.
What is Invanz 1g?
Invanz 1gm Injection is an antibiotic belonging to the carbapenem group that fights bacteria. It is used to treat severe infections of the skin, lungs, stomach, urinary tract, blood and brain (eg. meningitis).
How much lidocaine do I put in ertapenem?
Ertapenem, reconstituted with 1% lidocaine HCl injection, USP (in saline without epinephrine), is well absorbed following IM administration at the recommended dose of 1 g. The mean bioavailability is approximately 92%.
Can you reconstitute ertapenem with lidocaine?
Ertapenem, reconstituted with 1% lidocaine HCl injection, USP (in saline without epinephrine), is almost completely absorbed following intramuscular (IM) administration at the recommended dose of 1 g. The mean bioavailability is approximately 90%.
Can Invanz be given through a peripheral IV?
Nephron. 1976. INVANZ may be administered by intravenous (IV) infusion or intramuscular (IM) injection. When administered intravenously, INVANZ should be infused over a period of 30 minutes.
Can ertapenem be given IV push?
Several antibiotics are Food and Drug Administration–approved for IV push administration, including many beta-lactams. In addition, cefepime, ceftriaxone, ertapenem, gentamicin, and tobramycin have primary literature data to support IV push administration.
How do you reconstitute IV antibiotics?
Reconstitute a 1 g vial and a 2 g vial each with 10 mL of sterile water for injection • Administer each 1 g dose by slow IV push over 3 to 5 minutes. Administer each 2 g dose by slow IV push over 3 to 5 minutes. minutes. Local thrombophlebitis can occur.
How do you reconstitute antibiotics?
Using tap water and the measuring cylinder provided, measure out the required volume of water to reconstitute the oral antibiotic powder. Once the correct volume of water is measured, pour it slowly into the medicine bottle containing the oral antibiotic powder.
How do you reconstitute powder?
The reconstitution instructions on the label state to add 2 mL of sterile water to the vial to reconstitute the powder into a liquid form for injection. The label states that after the powder is reconstituted with the 2 mL of diluent, the concentration of fluid will be 225 mg/mL.
How many mL of diluent should be added?
How much initial sample and diluent should you use? Answer: 1:5 dilution = 1/5 dilution = 1 part sample and 4 parts diluent in a total of 5 parts. If you need 10 ml, final volume, then you need 1/5 of 10 ml = 2 ml sample. To bring this 2 ml sample up to a total volume of 10 ml, you must add 10 ml – 2 ml = 8 ml diluent.
What are the steps of reconstitution?
Adhere to the following steps to properly reconstitute REBLOZYL1
- Add Sterile Water for Injection, USP.
- Discard the needle and syringe used for reconstitution.
- Mix and wait.
- Inspect.
- Mix and wait.
- Repeat.
- Inspect.
Can Invanz be reconstituted with diluent?
INVANZ in ADD-Vantage® vials should be reconstituted with ADD-Vantage® diluent containers containing 50 mL or 100 mL of 0.9% Sodium Chloride Injection. Parenteral drug products should be inspected visually for particulate matter and discoloration prior to use, whenever solution and container permit.
What is Invanz 1GM injection?
Invanz 1Gm Injection is a carbapenem antibiotic which is used to treat intra-abdominal infections, community acquired pneumonia, acute gynaecological infections, diabetic foot infections of the skin and soft tissue. This medication should never be administered without consulting a doctor. Pregnant women are advised not to use this medicine.
Can Invanz be frozen for later use?
Solutions of INVANZ should not be frozen. Label: Refrigerate. Microbiology ( see below ). -Doripenem, imipenem, and meropenem cover most strains of P aeruginosa and Acinetobacter species. However ertapenem lacks sufficient activity. -Ertapenem is not indicated for enterococcal infections (lacks activity).
Can Invanz be used with a needleless IV?
NOTE: Use with a needleless IV system is not recommended. Shake well to dissolve and immediately withdraw a volume equal to 15 mg/kg of body weight (not to exceed 1 g/day) and dilute in 0.9% Sodium Chloride Injection to a final concentration of 20 mg/mL or less. Discard vial with unused portion of INVANZ reconstituted solution.