How do you use Acryl 60?
Mixing Instructions The normal ratio of Acryl 60® to clean potable water is 1 part Acryl 60® to 3 parts of water (1:3). Where increased physical and chemical resistance are required, increase the Acryl 60® content in the mixing liquid to a 1:2 or 1:1 Acryl 60® to water ratio. Always mechanically mix.
What does Acryl 60 do?
MasterEmaco A 660 (Acryl 60) is an acrylic-polymer concentrate is diluted up to 3:1 and is then mixed with portland cement mortars, plasters, stucco, and concrete mixes. Acryl 60 improves the adhesion, cohesion, tensile, compressive, and flexural strengths of these cement-based materials.
What is MasterEmaco a660?
MasterEmaco A 660 is an acrylic-polymer emulsion mixed with Portland cement mortars, plasters, stucco, and concrete mixes to enhance their physical properties, adhesion to substrates, and durability. Recommended uses: Interior or exterior. Above or below grade. Horizontal, vertical and overhead surfaces.
Who manufactures Thoroseal?
BASF
Cement-based, heavy-duty Waterproof coating for concrete and masonry, interior or exterior. Fills and seals pores and voids while resisting hydrostatic pressure. Mix with water and Acryl 60.
How do you apply Thoroseal waterproofing?
Start at the top and work down. Use a tampico fiber brush to apply Super Thoroseal® in a thick coat, working the mixture into the pores of the surface for a good penetrating seal. Double back and use the brush to smooth out the material. Allow 12 hours between coats for drying time.
Is Thoroseal waterproof?
Super Thoroseal® Waterproof Coating is a powder, cement-based waterproofing product for protecting concrete and masonry substrates. Easy to use, just add water. Coating can be applied to interiors and exteriors, above or below ground. Weatherproofs, seals out dampness with long lasting, decorative white finish.
How long does Thoroseal take to cure?
Allow Thoroseal® Foundation Coating to cure 7 – 10 days before immersion in water.
How do you seal a gap between concrete and House?
Seal cracks in concrete with durable urethane caulk. It’ll keep water out and protect your foundation and walks from further cracking and eroding. You can do it in less than a half hour.
Is acrylic concrete sealer good?
Acrylic sealers are great for stamped decorative concrete patios, driveways and pavers and really do beautify and enhance concrete’s aesthetic appearance. Our Take: We like Cryli-Tek 5505 with a nice wet-look that is non-yellowing and long lasting.
How do you use thoroseal foundation coating?
Mix ThoroSeal Foundation Coating with water and Acryl 60. Heavy, cement-based coating, bonding well with concrete and masonry substrates. Protects building interiors from dampness and moisture damage. Resistant to both positive and negative hydrostatic pressure. Will not ”blow off” exposed side of wall.
How much thoroseal do I use for varnish?
This coat should be half the thickness of the first coat. Try to apply 1 lb. of Thoroseal mixture for every square yard of the surface. Use an acrylic, polymer emulsion additive when mixing the Thoroseal with water to improve the coating’s effectiveness.
What is thoroseal and how does it benefit your home?
Keeping your house maintained can be hard work. Thoroseal is a building product manufactured by BASF Construction Chemicals. It is a waterproof cement-based coating that is used to fill, seal and protect interior and exterior surfaces.
How do you use a thoroseal brush?
Use a tampico fiber brush to apply the Thoroseal to the desired surface. Thoroughly brush the Thoroseal over the entire surface and make sure the surface is covered evenly. Aim for 2 lbs. of Thoroseal mixture for every square yard of the surface.